R-10-02-000427 6VXE7+ USER'S MANUAL 1. System power on by PS/2 Mouse: First, enable this function in CMOS Setup, then you can power on the syste
Quick Installation Guide 8 18. Pentium ® !!! 850/100MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 19. Pentium® !!! 533/133MHz FSB SW21 2 3 4 5 6 SW1
6VXE7+ 9 22. Pentium® !!! 733/133MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 23. Pentium® !!! 800/133MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 24.
Quick Installation Guide 10 II. Jumper setting : SPK : Speaker Connector PIIX4 6VXE7+ 82443BX PIN No. Function 1 VCC 2 NC 3 NC 4 Data External
6VXE7+ 11 PW LED : Power LED Connector PIIX4 6VXE7+ 82443BX PIN No. Function 1 LED + 2 LED − 3 LED − + − − HD : IDE Hard Disk Active LED PIIX4
Quick Installation Guide 12 GN : Green Function Switch PIIX4 6VXE7+ 82443BX PIN No. Function Open Normal Operation Close Entering Green Mode GD
6VXE7+ 13 Soft POWER : Soft Power Connector PIIX4 6VXE7+ 82443BX PIN No. Function 1 Signal 2 GND IR : Infrared Connector (Optional) PIIX4 6VX
Quick Installation Guide 14 ATX POWER : ATX Power Connector PIIX4 6VXE7+ 82443BX Pin No. Function 3,5,7,13,15-17 GND 1,2,11 3.3V 4,6,19,20 VCC 10
6VXE7+ 15 J2: CPU FAN PIIX4 6VXE7+ 82443BX PIN No. Function 1 GND 2 +12V 3 SENSE 1 J3: PWR FAN PIIX4 6VXE7+ 82443BX PIN No. Function 1 G
Quick Installation Guide 16 J15 :SYSTEM FAN PIIX4 6VXE7+ 82443BX PIN No. Function 1 GND 2 +12V 3 SENSE 1 IDE1: For Primary IDE Port 1 PIIX4
6VXE7+ 17 IDE2: For Secondary IDE Port 1 PIIX4 6VXE7+ 82443BX FLOPPY : Floppy Port 1 PIIX4 6VXE7+ 82443BX
Quick Installation Guide 18 LPT PORT / COM A / COM B PIIX4 6VXE7+ 82443BX COM B LPT PORT COM A JP1 : PS/2 Keyboard Power On Selection PIIX4 6VXE7
6VXE7+ 19 USB : USB Port PIIX4 6VXE7+ 82443BX PIN No. Function 1 USB V0 2 USB D0- 3 USB D0+ 4 GND 5 USB V1 6 USB D1- 7 USB D1+ 8 GND 1 2
Quick Installation Guide 20 JP9 : Clear CMOS Function PIIX4 6VXE7+ 82443BX PIN No. Function 1-2 close Clear CMOS 2-3 close Normal (Default) 3 2
6VXE7+ 21 J16: Internal Modem Ring On PIIX4 6VXE7+ 82443BX PIN No. Function 1 Signal 2 GND 1 JP10 : Case Open (Optional) PIIX4 6VXE7+ 82443BX
Quick Installation Guide 22 JP15 : Over Voltage(Magic Booster)(Optional) (When JP15 set ”Open”, CPU Voltage is rising 10%) PIIX4 6VXE7+ 82443BX PIN
6VXE7+ 23 J17 : Cyrix CPU Turbo Function (Optional) PIIX4 6VXE7+ 82443BX PIN No. Function open Normal short Turbo 1 JP17 : System After AC Back
Quick Installation Guide 24 BAT1 :Battery PIIX4 6VXE7+ 82443BX MDanger of explosion if battery is incorrectly replaced. MReplace only with the s
6VXE7+ 25 III. Top Performance Test Setting: Users have to modify the value for each item in chipset features as follow for top performance setting.
Quick Installation Guide 26 The following performance data list is the testing results of some popular benchmark testing programs. These data are jus
6VXE7+ 1 TABLE OF CONTENTS 1. INTRODUCTION 1.1. PREFACE...
6VXE7+ 1 The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a commitment to upd
Table of Contents 2 3.11. PERIPHERAL DEVICE INSTALLATION...3-8 3.12. KEYBOARD & PS/2 MOUSE INST
6VXE7+ 1-1 1. INTRODUCTION 1.1. PREFACE Welcome to use the 6VXE7+ motherboard. It is a Intel ® (CeleronTM /Pentium® !!! )and Cyrix Joshua Socket 37
Introduction 1-2 1.3. PERFORMANCE LIST The following performance data list is the testing results of some popular benchmark testing programs. These d
6VXE7+ 1-3 1.4. BLOCK DIAGRAM 24MHz 3.3V SDRAM DIMM Sockets 14.318MHz 33 MHz 33MHz Ultra DMA33/ ATA66 IDE Ports IDE Bus PCI Bus ISA Bus AGP Bus LPT
Introduction 1-4 1.5. INTRODUCE THE INTEL Socket 370 Processor Figure 1: INTEL Socket370 Processor 1.6 What is AGP? The Accelerated Graphics P
6VXE7+ 2-1 2. SPECIFICATION 2.1. HARDWARE • CPU − Support Socket 370 Processor: 300– 866MHz. − 370 pins 66/100/133MHz socket on board. • CHIPSET −
Specification 2-2 • I/O PORTS − Supports 2 16550 COM ports. − Supports 1 EPP/ECP LPT port. − Supports 1 Floppy port. − Supports 2 USB ports. − Suppor
6VXE7+ 3-1 3. HARDWARE INSTALLATION 3.1. UNPACKING The Motherboard package should contain the following: • The 6VXE7+ Motherboard. • USER’S MANUAL
Hardware Installation 3-2 3.2. MOTHERBOARD LAYOUT PIIX4 6VXE7+ 82443BXCPU SW2 VT82C596B VT82C 693A SW1 BIOS IDE 1 IDE 2 Floppy ATX POWERPS/2 USB BAN
6VXE7+ 3-3 t J3: PWR FAN Pin No. Function 1 GND. 2 +12V. 3 Sense. t J15: System FAN Pin No. Function 1 GND. 2 +12V. 3 Sense. t JP1: PS/2
Quick Installation Guide 2 I. Quick Installation Guide : The system bus speed can be set for 66,100,133MHz. The user can select the system bus speed (
Hardware Installation 3-4 t JP10 : Case Open (Optional) Pin No. Function 1 Signal 2 GND t J14: SB-LINK ( For PCI Audio / Sound Card use only ) P
6VXE7+ 3-5 PW : Soft Power Connector RST : Reset Switch Open: Normal Operation Short: For Hardware Re
Hardware Installation 3-6 3.4. DRAM INSTALLATION The Motherboard can be installed with 16 / 32 / 64 / 128 / 256 / 512MB (256Mb Technology) 168 pins D
6VXE7+ 3-7 Set System Bus Speed SW2: (O:ON / X:OFF) CPU PCICLK 1 2 3 4 5 6 66/100/ 133/Auto 33.3 X X X X O O 66 33.3 O O X X X
Hardware Installation 3-8 3.7. SPEAKER CONNECTOR INSTALLATION There is a speaker in AT system for sound purpose. The 4 - Pins connector SPK is used t
6VXE7+ 4-1 4. BIOS CONFIGURATION Award's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This
BIOS Configuration 4-2 4.2. CONTROL KEYS Up arrow Move to previous item. Down arrow Move to next item. Left arrow Move to the item in the left hand
6VXE7+ 4-3 4.3. GETTING HELP 4.3.1 Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. 4.3.
BIOS Configuration 4-4 • Chipset features setup This setup page includes all the items of chipset special features. • Power management setup This se
6VXE7+ 4-5 4.5. STANDARD CMOS SETUP The items in Standard CMOS Setup (Figure 4.2) are divided into 9 categories. Each category includes no, one or mor
6VXE7+ 3 Set System Bus Speed SW2: (O:ON / X:OFF) CPU PCICLK 1 2 3 4 5 6 66/100/ 133/Auto 33.3 X X X X O O 66 33.3 O O X X X X
BIOS Configuration 4-6 • Primary HDDs / Secondary HDDs The category identify the types of hard disk from drive C to drive F 4 devices that has been
6VXE7+ 4-7 • Floppy 3 Mode Support (for Japan Area) Disabled Normal Floppy Drive. Drive A Drive A is 3 mode Floppy Drive. Drive B Drive B is 3 mod
BIOS Configuration 4-8 • Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Base Memory The POST of th
6VXE7+ 4-9 4.6. BIOS FEATURES SETUP Figure 4.3: BIOS Features Setup • Virus Warning This category flashes on the screen. During and after the system
BIOS Configuration 4-10 • Boot From LAN First The default value is Disabled. Enabled Enable Boot From LAN First. Disabled Disable Boot From LAN Fir
6VXE7+ 4-11 • Memory Parity/ECC Check The default value is Disabled. Enabled Enabled Memory Parity/ECC Check Function. Disabled Disabled Memory Par
BIOS Configuration 4-12 • PCI/VGA Palette Snoop The default value are Disabled. Enabled For having Video Card on ISA Bus and VGA Card on PCI Bus. Di
6VXE7+ 4-13 4.7. CHIPSET FEATURES SETUP Figure 4.4: Chipset Features Setup • Top Performance The default value is Disabled. Enabled Enabled Top Pe
BIOS Configuration 4-14 • Read Around write The default value is Enabled. Enabled When set Enabled this feature speeds up data read performance. D
6VXE7+ 4-15 4.8. POWER MANAGEMENT SETUP Figure 4.5: Power Management Setup \ These two items will show up when “RTC Alarm Resume” is enabled. •
Quick Installation Guide 4 2. CeleronTM 333/ 66 MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 3. CeleronTM 366/ 66 MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3
BIOS Configuration 4-16 • Soft-off by PWRBTN The default value is Instant-off. Instant-off Soft switch ON/OFF for power ON/OFF. Delay 4 sec Soft sw
6VXE7+ 4-17 • LPT & COM The default value is LPT/COM. LPT/COM Enabled LPT/COM Ports Activity. NONE Normal Operation. LPT Enabled LPT Ports Act
BIOS Configuration 4-18 • RTC Alarm Resume You can set “RTC Alarm Resume” item to Enabled and key in date/time to power on system. The default valu
6VXE7+ 4-19 4.9. PNP/PCI CONFIGURATION Figure 4.6: PNP/PCI Configuration M IRQ[3.4.5.7.9.10.11.12.14.15] & DMA[1.3.5.6.7]These items will show
BIOS Configuration 4-20 • IRQ (3,4,5,7,9,10,11,12,14,15), DMA(0,1,3,5,6,7) assigned to The default value is "Legacy ISA" or "PCI/ISA
6VXE7+ 4-21 4.10. LOAD BIOS DEFAULTS Figure 4.7: Load BIOS Defaults • Load BIOS Defaults To load BIOS defaults value to CMOS , enter "Y".
BIOS Configuration 4-22 4.11. LOAD PERFORMANCE DEFAULTS Figure 4.8: Load Performance Defaults • Load Performance Defaults To load Performance defau
6VXE7+ 4-23 4.12. INTEGRATED PERIPHERALS Figure 4.9: Integrated peripherals ** This items will show up when ”UART2 Mode Select” is set to IrDA 1.0or A
BIOS Configuration 4-24 2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8. Disabled Disable onboard Serial port 1. • Onboard Serial Port 2 T
6VXE7+ 4-25 • UART2 Duplex Mode The default value is Half. Half Set UART2 Duplex Mode to Half. Full Set UART2 Duplex Mode to Full. • PS/2 Mouse
6VXE7+ 5 6. CeleronTM 466/ 66 MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 7. CeleronTM 500/ 66 MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 8. Celeron
BIOS Configuration 4-26 4.13. SUPERVISOR / USER PASSWORD When you select this function, the following message will appear at the center of the screen
6VXE7+ 4-27 4.14. IDE HDD AUTO DETECTION Figure 4.11: IDE HDD Auto Detection Type "Y" will accept the H.D.D. parameter reported by BIOS. Ty
BIOS Configuration 4-28 4.15. SAVE & EXIT SETUP Figure 4.12: Save & Exit Setup Type "Y" will quit the Setup Utility and save the us
6VXE7+ 4-29 4.16. EXIT WITHOUT SAVING Figure 4.13: Exit Without Saving Type "Y" will quit the Setup Utility without saving to RTC CMOS .
Appendix A-1 Appendix A: BIOS Flash Procedure BIOS update procedure: ü Please check your BIOS vendor (AMI or AWARD) on the motherboard. ü
6VXE7+ A-2 Appendix B : VIA Chipsets Driver Installation VIA 4 in 1 Service Pack Utility: Insert the support CD that came with your motherboard into
Appendix A-3 (7) (8) (9) (10) (11) (12) 6.Click “Next”. 7.Click “Next”.8.Click “Next”. 9.Click “Next”. 10.Click “Finish” to Restart Compute
FCC Compliance Statement: This equipment has been tested and found to comply with limits for a Class B digital device , pursuant to Part 15 of the F
Quick Installation Guide 6 10. Cyrix Joshua 300/100MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 11. Pentium® !!! 500/100MHz FSB SW21 2 3 4 5 6 SW1 O
Declaration of Conformity We, Manufacturer/Importer (full address) G.B.T. Technology Trading GMBH Ausschlager Weg 41, 1F, 20537 Hamburg, Germany
6VXE7+ 7 14. Pentium ® !!! 650/100MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 15. Pentium ® !!! 700/100MHz FSB SW21 2 3 4 5 6 SW1 ON 1 2 3 4 ON 16
Comentários a estes Manuais